![uv5r chirp programming not transmitting correct pl uv5r chirp programming not transmitting correct pl](https://i.ytimg.com/vi/c_lr29rH6H8/maxresdefault.jpg)
- #UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL HOW TO#
- #UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL MANUAL#
If your radio is not speaking (0) or is speaking Chinese (2), you know where fix this, Menu 14 to 1.ġ5, 16, 17, 18, 19, 20 Leave them alone for now. You will set up tones for repeaters later, but here set it to off.ġ4 VOICE set to 1 English. Set this to (0) off.ġ3 T-CTCS is Transmit CTCS Tones. You will set up tones for repeaters later, but here set it to off.ġ2 T-DCS is Transmit Digital Coded Squelch. Set this to (0) off.ġ1-R-CTCS is Receive CTCS Tones. MENU, 9 (or Up/Dn to select TOT), MENU, Up/Dn to select 60 seconds, MENU (to save), EXIT.ĭo you get the key sequence now? I'll just quickly now.ġ0 R-DCS is Receive Digital Coded Squelch. Also if you get long-winded, it will shut it off. This keeps you from transmitting too long if the PTT sticks, or you drop the radio between the seat and console. MENU, 8 (or UP/Dn to select BEEP), MENU, Up/Dn to select 0 (off), MENU (to save), EXIT.ĩ TOT is Time Out Timer. Default is On, but you can turn this off. Every time you press a button it will beep. MENU, 7 (or UP/Dn to select TDR), MENU, Up/Dn to select 0 (off), MENU (to save), EXIT.Ĩ BEEP. Turn this off for now so it doesn't screw up programming repeaters later. Dual Watch will allow the radio to flip-flop between two programmed channels, or two entered VFO frequencies going to whichever has traffic. It is recommended to turn off Dual Watch (7 TDR), especially while programming repeaters. MENU, 6 (or UP/Dn to select ABR), MENU, Up/Dn to select 5, MENU (to save), EXIT. Versions BFB291 and earlier are 0 - 5 seconds. MENU, 5 (or UP/Dn to select WN), MENU, Up/Dn to select Wide, MENU (to save), EXIT.īacklight Time Out is ABR (seconds) is submenu 6. MENU, 4 (or Up/Dn to select VOX), MENU, Up/Dn or 0, MENU (to save), EXIT. This is set from 0 (off) to 10 (maximum). MENU, 3 (or Up/Dn to select), MENU, Up/Dn or press 2, MENU (to save), EXIT. MENU, 2 (or Up/Dn to select TXP), MENU, Up/Dn to select High, MENU (to save), EXIT.īattery Save is submenu 3. While operating you can toggle High to Low and back without entering the menus by pressing the # key on the keypad. There are only two settings, High (about 4.5 watts) and Low (about 1 watt). MENU, 1 (or Up/Dn to select Step), MENU, Up/Dn to select 5.0 khz, MENU (to save), EXIT.
![uv5r chirp programming not transmitting correct pl uv5r chirp programming not transmitting correct pl](https://i.ytimg.com/vi/0l_kdktZAkI/maxresdefault.jpg)
![uv5r chirp programming not transmitting correct pl uv5r chirp programming not transmitting correct pl](https://www.bugoutbagbuilder.com/sites/default/files/images/Bug-Out-Bag-Builder-Baofeng-UV-5R--Basic-Setup-%26-Emergency-Frequencies-2.jpg)
Next is 1 Step (Frequency Step), with steps from 2.5 khz up to 50 khz. MENU, 0 (or Up/Dn to select SQL), MENU, 7 (or Up/Dn to select), MENU (to save), EXIT. I set mine to 7 due to a lot of RF breaking squelch locally. Press Exit to exit and return to regular operation. Press MENU again to exit and save the change. Make your selection in the submenu using the Up/Dn buttons or enter a number. Or enter the submenu number if you know it. Use the Up/Dn arrow buttons to scroll up and down the list of submenus.
![uv5r chirp programming not transmitting correct pl uv5r chirp programming not transmitting correct pl](https://obrazki.elektroda.pl/2130949100_1509137780.png)
The menus are all set and adjusted with this basic key sequence: You cannot manually program with it set to B line.įrequency Mode, A line. You must set the blue A/B button so that the cursor on the left side is on the upper frequency line. You cannot manually program in MR or Memory Recall (voice says "Channel Mode").
#UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL MANUAL#
Meanwhile, download and print this Menu description.īefore you start manual programming, you should get some initial "set once and forget" settings done.įIRST you must set the orange VFO/MR button so that the voice says "Frequency mode" (VFO). In my next post I'll go over manual programming.
#UV5R CHIRP PROGRAMMING NOT TRANSMITTING CORRECT PL HOW TO#
The Miklor site above tells you how to fix your Prolific driver problems IF it has a fake Prolific driver. Click the "Go Get It" button to download this good manual. Here is a great English manual not written by the manufacturer. There are two sites you need to bookmark, where you can find all that I am going to outline, the Miklor site, and the UV-5R yahoo group. The earlier China Girl versions work as well as the later ones. It will come in handy later.Ībout version 251, the English voice was changed from a Chinese accent, known as "China Girl" to an American accent. They all have BFB, so all you have to look for are the last three digits. For just a second or two you will see the firmware number such as BFB281. Press 3, and while holding it, turn the radio on. To find out your firmware version, turn the radio off. No one is better than another, and the "latest firmware" is not a better performing radio than the older ones. They all work just as well, but you run into some programming and cloning problem across some firmware versions. There is no difference, they all have the same chassis and circuitry. The Baofeng UV-5R, and related models, -5RA, -5R+, etc, are all the same under the skin. I'm figuring out to do "hot links" here, so here goes. On another thread I had said I would post something on programming the Baofeng UV-5R.